Products
COMAC "HIGH-VOLUME" EXTRUDERS (D/d ratio ≈ 1.65)
Series HT (11 Nm/cm3) and series XT (15 Nm/cm3)
Series HT (11 Nm/cm3) and series XT (15 Nm/cm3)
| Model | EBC 25 | EBC 40 | EBC 50 | EBC 60 | EBC 70 | EBC 90 | EBC 120 |
| Nominal diameter (mm) | 27 | 43 | 55 | 64 | 72 | 94 | 123 |
|
Screw number of lobes |
2 | 2 | 2 | 2 | 2 | 2 | 2 |
|
Screw center to center (mm) |
22 | 35 | 44,6 | 52 | 58 | 76 | 100 |
|
Screw speed (rpm) other values on request |
600 900 1200 |
600 900 1200 |
600 900 1200 |
600 900 1200 |
600 900 1200 |
600 900 1200 |
300 600 |
|
Torque on each screw (Nm) HT(Hign torque) XT(Extra torque) |
117 160 |
472 643 |
976 1331 |
1547 2109 |
2146 2927 |
4829 6585 |
11000 15000 |
| L/D ratio | 32 ÷ 48 | 32 ÷ 48 | 32 ÷ 48 | 32 ÷ 48 | 32 ÷ 48 | 32 ÷ 48 | 32 ÷ 48 |
| Output (Kg/h) |
30 ÷ 90 |
120 ÷ 400 |
230 ÷ 750 |
350 ÷ 1250 |
550 ÷ 1850 |
1150 ÷ 3800 |
1350 ÷ 4500 |
Remarks:
L/D -- tipically, barrels are built-up by independently thermoregulated modules having 4 diameter lencth each;
Output -- the ranges here above want to give an idea on limits considering a variety of cases, but, figures can only be very indicative;
actually achievable values strongly depend on raw material formulations, target product and relevant desired characteristics, as well as speed and process conditions.
L/D -- tipically, barrels are built-up by independently thermoregulated modules having 4 diameter lencth each;
Output -- the ranges here above want to give an idea on limits considering a variety of cases, but, figures can only be very indicative;
actually achievable values strongly depend on raw material formulations, target product and relevant desired characteristics, as well as speed and process conditions.
COMAC "STANDARD" EXTRUDERS (D/d ratio ≈ 1.5)
Series HT (11 Nm/cm3) and series XT (15 Nm/cm3)
Series HT (11 Nm/cm3) and series XT (15 Nm/cm3)
| Model | EBC 25 | EBC 40 | EBC 50 | EBC 60 | EBC 70 | EBC 90 | EBC 120 |
| Nominal diameter (mm) | 26 | 42 | 53 | 62 | 70 | 92 | 120 |
|
Screw number of lobes |
2 | 2 | 2 | 2 | 2 | 2 | 2 |
|
Screw center to center (mm) |
22 | 35 | 44,6 | 52 | 58 | 76 | 100 |
|
Screw speed (rpm) other values on request |
600 750 |
600 750 |
600 750 |
600 750 |
600 750 |
600 750 |
300 600 |
|
Torque on each screw (Nm) HT(Hign torque) XT(Extra torque) |
117 160 |
472 643 |
976 1331 |
1547 2109 |
2146 2927 |
4829 6585 |
11000 15000 |
| L/D ratio | 32 ÷ 48 | 32 ÷ 48 | 32 ÷ 48 | 32 ÷ 48 | 32 ÷ 48 | 32 ÷ 48 | 32 ÷ 48 |
| Output (Kg/h) |
25 ÷ 60 |
100 ÷ 250 |
200 ÷ 500 |
300 ÷ 750 |
500 ÷ 1400 |
1000 ÷ 2200 |
1200 ÷ 4000 |
Remarks:
L/D -- tipically, barrels are built-up by independently thermoregulated modules having 4 diameter lencth each;
Output -- the ranges here above want to give an idea on limits considering a variety of cases, but, figures can only be very indicative;
actually achievable values strongly depend on raw material formulations, target product and relevant desired characteristics, as well as speed and process conditions.
L/D -- tipically, barrels are built-up by independently thermoregulated modules having 4 diameter lencth each;
Output -- the ranges here above want to give an idea on limits considering a variety of cases, but, figures can only be very indicative;
actually achievable values strongly depend on raw material formulations, target product and relevant desired characteristics, as well as speed and process conditions.
| Comac S.R.L. 20023 Cerro Maggiore(Mi), via Legnano 57 - tel. +390331577387 - partita IVA 09986760156 |